首页 > 新闻动态 > > Installing , ensure that the ferrule cuts into the pipe
新闻动态
新闻
  • NPT线程和NPTF线程之间的区别

    1. NPT和NPTF螺纹是美国最常用的锥形管螺纹,用于应用,从电管和扶手到运输气体或腐蚀性液体的高压线。NPT用于机械或低压气体以及需要使用密封剂...
  • 液压管件类型

    液压管件类型 1,NPTF锥形螺纹接头 注意:这是干密封螺纹;它是用于输送燃料的家用锥形管螺纹。它可用于外螺纹和内螺纹末端接头。 NPTF外螺纹可以...
  • 316不锈钢水管较厚

    316条不锈钢水管的产物质量在于其热量和压力抗性,而高温抗性和压力则是...
  • 咬合式管件

    公制螺纹咬合式管接头由主体,切割环和螺母三部分组成,当将切割环和螺母插入钢管上的接头体内并拧紧螺母时,切割的外端密封圈应安装在接头主体的...
  • 2024年春节假期在中国,并注意客户

    亲爱的顾客,中国的2024年春节假期正在临近。祝大家在新的一年中一切顺利 运输通知: 对于需要在新年之前运送的货物,请在2月4日之前通知我们。官...
  • 如何使用管道和管件

    液压系统的管件包括油管和管件,它们连接到各种类型的液压元件上,输送压力油的装置。 管道配件应具有足够的耐压强度(强度),无泄漏,压力损失...
  • 2021年新年快乐

    从2021年2月19日开始,全体员工已开始工作。 祝你新年快乐
  • The Standard for Common Tube Fittings

    National standard (GB), electricity standard (DL), petroleum and petrochemical standard (SY), mechanical department standard (JB), chemi...
  • 带旋转螺母的90度弯头减速器管接头

    90度弯头减速器管接头带旋转螺母伊顿型号:2C9,2D9派克型号:EW产品描述:DIN标准适配器,公制公头24°......
  • 卡套式管接头的安装方法和说明

    一,卡套连接器的安装方法: 1.锯切一段合适的无缝钢管,以去除端口上的毛刺。管道的端面应垂直于轴线,且角度公差不超过0.5°。如果需要弯曲管子...
联系我们
江苏宜城流体设备有限公司
销售经理:Jason Gao
电子邮件:sales01@yc-lok.com.

Installing , ensure that the ferrule cuts into the pipe

Luna 2021-09-18 10:32:34
1. The pipes to be pickled shall be pickled first as required;

2. Cut the pipe with sawing machine or special pipe cutting machine according to the required length, and it is absolutely not allowed to cut with melting or grinding wheel; Remove burrs, metal chips and dirt on the inner and outer circles of the pipe end; Remove rust inhibitor and dirt from pipe joints; At the same time, ensure the roundness of the pipe;

3. Insert the nut and ferrule into the pipe successively. The front edge of the ferrule shall be at least 3mm away from the pipe opening, and then insert the pipe into the conical hole in the joint until it is pushed;

4. Slowly tighten the nut and rotate the pipe until it does not move, and then tighten the nut for 2 / 3 ~ 4 / 3 turns;

5. Disassemble and check whether the ferrule has been cut into the pipe and whether the position is correct. The ferrule is not allowed to move axially, but can rotate slightly;


6. Tighten the nut again after passing the inspection.